Parking System 4S Automatic Barrier Gate With Loop Detector /
Photocell
What are the disadvantages of the Wonsun Automatic Barrier Gate?
1)The humanized clutch device: in case of power off, unlock the
clutch device and raise the boom manually. By the time the power is
supplied, lick the clutch device to make it work normally again.
2)Special spring device: Both the compression spring and tension
spring can be used in the machine, Using the compression spring can
avoid accidents caused by the tension spring.
3)Three control buttons: for boom raising, falling, and pausing.
4)Boom backtrack function: the boom will rise if hits something
when falling.
5)Infrared photocell design: for avoiding the crash when the boom
falls, so as to prevent the vehicles from being pressed.
6)Both external and internal loop detectors are supported.
7)"open", "close" and "stop" controlling interfaces.
8)RS-485 communication serial interface(optional)
9)Traffic light signal connection device: red light for stop, green
light for pass.
10)Automatic Barrier Gate Remote control and wire control for
selection.
Automatic Barrier Gate Model Selection and Differences
Automatic Barrier Gate Specifications
Automatic Barrier Gate Model | WST1211 |
Automatic Barrier Gate Working Temperature | -40℃～+75℃ |
Automatic Barrier Gate Voltage | 220V±10%, 110V±10%, 50/60HZ |
Automatic Barrier Gate Rated power | 80W |
Automatic Barrier Gate Relative humidity | ≤90% |
Automatic Barrier Gate Remote control distance | ≥30m |
Automatic Barrier Gate Net weight | 48kgs |
Automatic Barrier Gate Speed | 1S,1.8S,3S, 6S |
Automatic Barrier Gate Max boom length | 6 meters |
Automatic Barrier Gate Motor Rotational speed | 1400rmp |
Automatic Barrier Gate Protection Degree | IP44 |
1 pcs Automatic Barrier Gate
1 pcs Automatic Barrier Gate arm boom (from 1m to 6m can
customized)
1 pcs Automatic Barrier Gate control panel(built inside)
2 pcs Automatic Barrier Gate, remote controllers
1 pcs Automatic Barrier Gate manual book
Communication with customers
1) Q: Connected power and pressed the open/close button but the Automatic Barrier Gate did not action.
A | Reason | Solution |
1 | Fuse blown | Check the fuse and power in the controller |
2 | The battery of the remote control powered off | Change a new one |
3 | External protection circuit break or at protecting status | Open the barrier door and click the OPEN/CLOSE button on the
control box |
4 | Same frequency interference | Check photocell and loop detector |
2) Q: Connected power and press the open/close button, The
automatic Barrier Gate will move but even when it is in the right position, the motor
still runs and does not stop.
A | Reason | Solution |
1 | Limit switch | Adjust the horizontal/vertical limit switch to the correct position |
2 | Main controller failure | Change a new one |
3) Q: The motor running but the Automatic Barrier Gate arm is not in action.
A | Reason | Solution |
1 | Barrier arm at 45° position where is hard to move | Unlock the clutch and manually rotate the arm to a horizontal or
vertical position then try again |
2 | The tension of the balancing spring is not suitable | Adjust spring exactly |
3 | Low working voltage | Check the voltage and power |
4) Q: When opening/closing, the Automatic Barrier Gate arm cannot reach the right position (90° vertical & 180°
horizontal).
A. | Reason | Solution |
1 | Length adjustment of connecting rod not correct | Open the barrier door and unlock the clutch to check when the arm
is at 90° vertical position if the master rod covers slave one; when the arm
is at 180° horizontal position if the master rod and slave one are in the
same straight line |
2 | Nuts on the limit switch loose | Tighten the nuts when arm at 90° vertical and 180° horizontal
|
Automatic Barrier Gate Basic Features:
1)By security. The barrier gate will automatically go back when
meets obstacles during closing.
2)Automatic Barrier Gate AC motor is more powerful and no
maintenance.
3)Automatic Barrier Gate arm can be chosen from 3 meters to 6
meters, and barrier gate.
4)Closing time is also arranged from 1 second to 6 seconds.
5)The Automatic Barrier Gate can be both right-installed and
left-installed.
6)All the operation processes are soft without any noise and
shaking.
7)Infrared photocell interface, loop detector interface, and IC
system.
8)The interface is reserved for the other functions.
9)Green light and red light are used inside for indication of the
position of the boom
Automatic Barrier Gate Advanced Features:
1) A clutch key can be used to open the clutch when power is off.
2)Fan cooling machine reduces the motor temperature by high
frequency using, never get heat-protecting, unique temperature
calefaction design for low temperature using, prevent freezing in
cold weather.
3) An exactitude aluminum alloy die-casting motor base reduces the
noise and joint abrasion to prolong the barrier gate's working
life.
Automatic Barrier Gate Automatic Barrier Gate Automatic Barrier
Gate Automatic Barrier Gate Automatic Barrier Gate Automatic
Barrier Gate Automatic Barrier Gate Automatic Barrier Gate
Automatic Barrier Gate Automatic Barrier Gate Automatic Barrier
Gate Automatic Barrier Gate
Contact us for pricelist and catalog:
Sue Zhang
Email:sue@wonsunbarrier.com
Skype: SueZhang729
Whatsapp:+86 158 7925 9831
